BB30 service kit for SRAM DUB cranks. - Includes (2) Enduro 6806/29 ABEC-3 sealed bearings and 2 retaining clips - Bearing Dimensions: OD: 42mm / ID: 29mm / Width: 7mm - Enduro ABEC-3 bearings - Use with SRAM DUB cranks Note: SRAM DUB cranksets are not designed to work in 68mm or 73mm wide shells with inboard bearings. Use only if your frame is a direct-fit bearing system, and the BB shell width is 86.5mm or wider.
Wheels Manufacturing open bore adapters are used to press sealed cartridge bearings into place. The adapters are machined with one step to correspond to the bearing OD, which fits in to the center of the sealed bearing and an outside diameter to accommodate the bearing's outer diameter. Size: [Bearing inner diameter] x [Bearing outer diameter] Note: If only one dimension is given, that is the outer diameter of the adapter, with no inner diameter step
6-piece screwdriver set with Kraftform Plus handle for pleasant, ergonomic working that prevents blisters and calluses. - Hard gripping zones for high working speeds, while soft zones ensure high torque transfer - Partially Lasertip: the tip literally bites into the head of the screw and thereby prevents any slipping out of the screw head - "Take-it-easy" Tool Finder: color coding according to profile and size. - The hexagonal anti-roll feature prevents any bothersome rolling away at the workplace - Includes practical rack for tidy storage of the screwdrivers - Screwdriver for slotted and cross-recess screws, Phillips - Multi-component Kraftform handle for fast and ergonomic screwdriving
High-quality L-key set out of stainless steel for hexagon socket screws by Wera. The Hex-Plus profile offers a greater contact surface in the head of the screw; the notching effect is therefore reduced to a minimum and damage to the screw head is more or less eliminated. Comes with hex ballpoint on the long arm: the ballpoint drive profile means that it is possible to swivel the tool axis away from the screwdriving axis, thus enabling "round the corner" screwdriving. - Stainless steel prevents the transfer of extraneous rust: fasten stainless screws with stainless tools - Hex-Plus allows socket head screws to live longer - With Take-it-easy tool finder: color coding by size - Wear-resistant clip material for enhanced durability - Color-coded, easy-to-grip plastic sleeve, even at low temperatures - Comes in an almost wear-free L-key clip fastener
$8.99 - $29.99
WPL Wet Chain Lube is a premium bio-based chain lube providing efficient pedaling and long-lasting performance to cyclists of all disciplines. Formulated specifically for wet conditions and long-distance riding, proprietary Emulsifite technology allows for easy cleaning of the chain after long rides by dissolving under high-pressure water. The concentration of Emulsifites in the lube has been fine tuned to resist puddle and rainwater but to activate under high-pressure water from a hose. All you have to do is spray your chain with water after your ride, and the accumulated dirt and grime will disappear. - Premium bio-based formula made with natural ingredients - Emulsifite technology provides dynamic cleaning abilities and prevents black goop build-up - Long-lasting formula improves pedal efficiency by reducing chain wear and friction - For use on bicycle chains, shifters, derailleurs and cables - Biodegradable, non-toxic, PTFE-free formula is environmentally friendly
$5.19 - $127.10
- Light viscosity oil for deep penetration with teflon for durability - Law prohibits orm-D materials from shipping by air
Topeak's sleek FlashStand Slim is a super parking/display stand that folds up for pocket-sized portability. This affordable, lightweight wonder securely holds your bike by the non-drive side crankarm to keep it upright and safe. Take it along in your jersey pocket for those quick pit stops, too!
Attach this handy multi-tool to your Specialized SWAT-equipped water bottle cage (sold separately) and hit the trails secure in the knowledge that your tools are close at hand. The tool features hardened steel bits with an anti-rust coating and the plastic tool cradle holds securely and rattle-free thanks to the two attachment points.
This Zee Cage II was designed with an integrated EMT Cage Mount MTB Tool that has all of the trailside necessities required to get you out of a jam on your ride. For the cage itself, you'll find it to be respectably lightweight, and to have incredible holding power for when the trails get rough. For easy bottle access, we also gave it a unique side-loading design that allows you take pulls from the right or left-hand side depending on placement. - SWAT design allows for storage and tool integration. - Reinforced composite material improves durability without adding weight. - Includes EMT Cage Mount MTB Tool with 3, 4, 5, 6, 8mm, T25 Torx, and #1 flathead screwdriver. - Right-hand loading on the down tube—left-hand loading on the seat tube. - Sleek, minimalist design with razor-sharp graphics.
SRAM Bleeding Edge Tool. - Use with Avid or SRAM Pro Bleed Kit
DOT 5.1 brake fluid is compatible with all SRAM and Avid hydraulic disc brakes - Brake Fluid Type: DOT 5.1 - Bottle Size (Brake Fluid): 4 oz - Application (Brake Fluid): Disc Brakes
SRAM's Disc Brake Bleed Kit has everything you need to ensure your brakes are dialed. The kit is compatible with SRAM X0, XX, Guide, and HydroR brakes. It is not compatible with RockShox' fork bleed kit. Includes the following: • 2 syringes/fittings • bleed blocks • Torx tool • Crow's foot • Bleeding Edge Fitting • DOT 5.1 hydraulic fluid
- Improved sealing and durability - New rotating metal hose fittings - High-volume hose with clamp - Longer lasting - Must-have for all mechanics - DOT 5.1 - NOT compatible with RockShox fork bleed kit
$10.00 - $23.00
• Service kits include air can seals and wiper • Available for RockShox air rear shocks--Ario, Monarch, Monarch RT3, DebonAir and Monarch Plus
$6.00 - $24.00
Keep your Reverb dropper post performing at its best with RockShox's Reverb Hydraulic Fluid. It's optimized for the remotes of the Reverb as well as the Monarch XX rear shock.
$11.00 - $19.95
Rock-N-Roll Extreme is a very clean lubricant due to its ability to shed dirt and dust. - For mountain bike or wet road riding
$12.99 - $33.00
- Xtreme chain lube is formulated for long-distance and extreme off-road conditions - MFR bonds to metal surfaces and resists build-Up and tackiness, in addition to shedding water
This complete set has everything needed to remove cassettes from the hub. Its dual compound handle offers extra grip and comfort. - Integral safety pin on cassette remover - Designed for Shimano cassettes
Lightest, Strongest most versatile portable tool! Reversible ratchet with Quick-Disc thumb wheel. Handle is a Prestalever Tire Lever! Carry only the bits you need w/trim-able bit carrier. Patented Ratchet Mechanism Stronger than all others. Patented 1/4" Bit Retention with Push-to-Remove Hole. Hex: 2mm, 2.5mm, 3mm, 4mm, 5mm, 6mm, 8mm TORX: T6, T8, T10, T15, T20,T25, T30 Screwdrivers: PH0, PH1, PH2 1/8 flat, 3/16 flat
A great way to make cleaning easier is to remove your wheels. While this may seem excessive, removing the wheels from your bike opens up many tight areas that are tough to clean, allowing easier access and better visibility of these surfaces. The Pedro's Chain Keeper was designed with this wheels-off technique in mind and makes sure your chain stays off your frame, preventing damage and keeping your drivetrain free to turn as is commonly needed during cleaning. Try it out! The Chain Keeper inserts into the right rear dropout when the wheel is removed for cleaning, storing, or transporting your bike. The quick-release lever allows for fast and easy installation and removal.
- Perfect companion for your Pedro's torque wrench - Bits made from premium S2 tool steel to ensure strength and lasting performance - Includes 16 hex and torx bits and 2 drive adapters in convenient holders - 50mm length bits in key sizes ensure component compatibility Pedro's Hex Bit Set II is designed to work with our torque wrenches offering an extensive range to handle most hex and torx needs. The set includes longer 50mm bits in key sizes to ensure compatibility and fit with all components where standard 25mm bits fall short. Bits are made from premium S2 tool steel for strength and lasting performance. Set includes: - Hex: 2, 2.5, 3, 4, 5, 6, & 8mm (25mm), 4 & 5mm (50mm) - Torx: T10, T15, T20, T25, & T30 (25mm), T25 & T30 (50mm) - Drive Adapters: 1/4-inch square to 1/4-inch hex & 1/4-inch hex to 1/4-inch square
Park Tool introduced the bicycle world to the 3-way hex wrench set over 30 years ago. Our 3-way wrenches fit perfectly in the palm of the hand and provide excellent leverage, making them a favorite of countless shop mechanics worldwide. AWS-1 FEATURES - 4mm, 5mm, and 6mm hex set - Wrenches made from industrial tool steel, through hardened and tempered for long life - Chamfered tips for a perfect fit
Park Tool introduced the bicycle world to the 3-way hex wrench set over 30 years ago. Our 3-way wrenches fit perfectly in the palm of the hand and provide excellent leverage, making them a favorite of countless shop mechanics worldwide. AWS-3 FEATURES - 2mm, 2.5mm, and 3mm hex set - Wrenches made from industrial tool steel, through hardened and tempered for long life - Chamfered tips for a perfect fit
Featuring a forged, two-piece, anodized, ergonomically designed aluminum body and replaceable hex wrenches, Park Tool's Aluminum Body 3-Way Hex Set is a mechanic's dream. 4mm, 5mm, and 6mm wrenches are made from industrial strength, heat-treated steel for long life.
The BKD-1 Hydraulic Brake Bleed Kit will bleed most models of DOT-fluid-based hydraulic brakes. Hydraulic systems need bleeding to remove any air bubbles and to inject new, clean fluid. - Designed and built for home use and the rigors of daily commercial use - Includes two syringes, hoses with shutoff clips, multi-size bleed blocks and a unique attachable syringe mount - Housed in a rugged reusable case - Machined stainless steel and 7075 aluminum fittings to service SRAM, Hayes, Formula, Hope and other brands of DOT-fluid-based hydraulic brake systems - Replacement parts available - Brake fluid not included
The BX-2.2 features updated pallet configuration and storage options to help you keep your tools secure and easily accessible. The expanded custom designed tool pallets, including dual-sided pallet wings, are all housed in a virtually indestructible composite travel case. Designed and built for the traveling mechanic who demands the best! - Custom designed tool-holding pallets with loops and pockets - Folding, dual-sided pallet wings - Front tool pallet that stores securely inside during transport - Dent-proof composite shell built around an aluminum frame - Key lock - Nominal dimensions: 19" x 14.85" x 8.5" (48.25 cm x 37.7 cm x 21.6 cm), 13.2 lbs. (6 kg)
A complete tool set to work on both Campagnolo and Fulcrum Ultra-Torque and Power Torque crank and bottom bracket systems (each sold separately). The CBP-8 includes a beefed-up bearing and crank puller and all the fittings necessary to remove and install both systems. - Bearing Puller That Fits Both Power Torque And Ultra-Torque - Crank Puller For Power Torque - Bearing Setter For Both Power Torque And Ultra-Torque - Removal Adaptor For Power Torque Crank Bearings - Removal Protection Pads For Use With Carbon Cranks - Removal Protection Adaptor For Use With Aluminum Crank Arms - Crank Removal Extension Plug For Power Torque
Heat-treated alloy tool steel, one inch base fits wrench or bench vise. Thin-wall construction allows use without removal of cones and locknuts. The FR-5 has 12 splines that are approximately 23.4mm across. - Fits Shimano, SRAM, Sunrace, Suntour, Chris King and other cassette lockrings - Fits the SRAM XX1 11-speed cassettes - Also fits Shimano disc brake lockrings - Always use a quick-release skewer to hold the tool in place and snug to cogs when loosening; for solid axles, use the axle nut
A favorite of shop mechanics for over 30 year's, Park's CCP-22 Crank Puller removes crankarms that feature square tapers, and those that fit on Power Drive and Power Spline bottom bracket interfaces. The long, comfortable, built-in handle and fine thread provide the leverage needed to remove even the tightest crankarms. And, there's a rotating tip to ensure smooth operation and long life.
Park's Double-Ended Cone Wrenches are designed for home mechanics. They're made of thin tool steel to fit the low-clearance adjusting nuts and cone flats on a variety of bearing assemblies. Each wrench is chrome plated for long life and available in popular combinations from 11 to 18mm. Most applications require a pair of cone wrenches. Call or stop by. We can recommend the correct sizes for your needs.
Page 1 of 38 Next page